Sites Grátis no Comunidades.net


Total de visitas: 18535
Frame Relay Point To Multipoint Pdf Download

 

Frame Relay Point To Multipoint Pdf Download >>> http://shurll.com/bjse2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frame Relay Point To Multipoint Pdf Download

 

R1 con0 is now available Press RETURN to get started. Interface Serial0/0 set to default configuration R1(config)# %LINEPROTO-5-UPDOWN: Line protocol on Interface data communication and computer network pdf free download changed state to down R1(config)#interface Serial0/0 R1(config-if)#encapsulation frame-relay R1(config-if)#interface serial0/0.123 multipoint R1(config-if)#ip address 10.54.123.1 255.255.255.248 R1(config-if)#frame map ip 10.54.123.2 122 broadcast R1(config-if)#frame map ip 10.54.123.3 123 broadcast R1(config-subif)#end R1# %SYS-5-CONFIGI: Configured from console by console R1#show frame-relay map Serial0/0.123 (up): ip 10.54.123.2 dlci 122(0x7A,0x1CA0), static, broadcast, CISCO, status defined, active Serial0/0.123 (up): ip 10.54.123.3 dlci 123(0x7B,0x1CB0), static, broadcast, CISCO, status defined, active R1# Objective 4 From R2 and R3 verify IP connectivity to the hub as well between the spokes using the new point-to-multipoint configuration on R1. (Watch de video) Frame-Relay Point to Multipoint Topology As you have already seen we will configure R1 interface as multipoint but R2 and R3 as point-to-point. Configure R1s Serial0/0 interface with two frame relay maps. To create a multipoint subinterface, enter multipoint instead:.

 

Last modified by ISMAIL (CCIE (Written) /CCSP/CCNP/JNCIS-ER/MCSA) on Jul 28, 2011 2:23 pc problem solution pdf download In this lab youll familiarize yourself with the following new command; Command Description frame-relay map ip x.x.x.x dlci# braodcast This command when executed in the physical serial interface or point-to-multipoint sub-interface configuration mode maps a specific IP Address to a specific DLCI. Reply Sami November 13, 2013 at 11:19 am jeaniene frost once burned free pdf download I think I found the reason, please find the attached link Reply Sami November 13, 2013 at 11:03 am # lawangeen your post is totally correct. (I may need to read that part twice to understand it) show frame-relay map This command when executed in privileged mode will display all frame-relay ip to dlci mappings, rather they are static (using the frame-relay map) command or dynamic; which are learned by Inverse ARP which will be discussed in the next lab. Show 0 comments Comments Show comments: 0 Comments 0 Author comments Name Email Address Website Address Name (Required) Email Address (Required, will not be published) Website Address Delete Document Close Are you sure you want to delete this document? Actions Log in / Register to participate in the community & access resources like: IT Training Videos and Seminars Cisco Certification Study rusty cooley arpeggio madness pdf download Cisco Certification asian bridal magazine download pdf Topics Register for free now. When you specify broadcast after the DLCI number this enables broadcast on that DLCI. Note: If youve completed the lab prerequisites you should have full IP communications between all 3 routers as shown below; R2#ping 10.54.123.1 Type escape sequence to abort. Verify the Frame-Relay Map statements using the show frame-relay map command From R2 and R3 verify IP connectivity to the hub as well between the spokes using the new point-to-multipoint configuration on download buku dumairy perekonomian indonesia pdf Sending 5, 100-byte ICMP Echos to 10.54.123.3, timeout is 2 seconds: guia de coleopteros pdf download Success rate is 100 percent (5/5), round-trip min/avg/max = 28/136/300 ms R2# Objective gadgets and gizmos magazine jan 2013 pdf file free download

 

A frame Relay map will allow you to map an IP address to a DLCI number, this makes the router send traffic that is destined towards that IP address to take the specified DLCI number in the frame relay map. Reply pragash January 5, 2014 at 2:50 pm # After searching every where in the internet&. Can some one explain that why the ping from R1 to IP address ip address 192.168.0.1 onion farming in kenya pdf download is not working. c language files pdf download completed all i got only frame-relay router connected updates not other and i used no ip split-horizon eigrp 1003 but doesnt iffect Reply yellow January 6, 2015 at 12:07 am # 1. Latest Tweets 9 months ago The fccnawb website is not only available in HTTPS. This is necessary when using dynamic routing protocols.Router(config-if)#no frame-relay inverse arpTurns off Inverse ARP.Router#show frame-relay mapDisplays IP/DLCI map entriesRouter#show frame-relay pvcDisplays the status of all PVCs configuredRouter#show frame-relay lmiDisplays LMI statisticsRouter#clear frame-relay countersClears and resets all Frame Relay countersRouter#clear frame-relay inarpClears all Inverse ARP entries from the map tableRouter#debug frame-relay lmiUsed to help determine whether a router and Frame Relay switch are exchanging LMI packets properly. Regards Reply . Remove from profile Feature on your profile More Like This Retrieving data . 10 months ago Interested in following the Founder of the Free CCNA Workbook website? Check out MattGeorgeCCIE Useful Links Stub Lab GNS3 Topology File Download GNS3 - Cisco Device Emulator Download Reddit.com CCNA Community Junos Workbook Free Juniper JNCIA Training Putty Terminal Emulator (Free Download) Quiz Me! - CCNA R&S Practice Exam Copyright 2009-2014 Free CCNA Workbook All Rights Reserved. e913ce18fc